XNORIT-WAN - xnorit:public:summary

3dprinterenclosure

Anonymous (anonymous@undisclosed.example.com) — 2024-11-06T11:42:39+00:00

3D printer enclosure After purchasing a Prusa MK4, I wanted to put it in it's own enclosure with air-ventilation on it. This as many prints take a while, the fumes are unpleasant to sit in, and it's probably not that healthy as well... Prusa MK4 kit

curtainsteppermotordriver

Anonymous (anonymous@undisclosed.example.com) — 2024-10-12T13:30:06+00:00

Curtain stepper motor As I was busy automating many things in the house, I decided to also automate my curtains using the Xnorduino bus system. The steppermotor drivers have been completed and an (early) example video has been added to this page. I've however not been able to install these motors above my windows yet, as no cat6 communication and power cabling has been foreseen during recent renovations. That's something I'm planning to finalize around early november / end of december.

freezermonitoringsystem

Anonymous (anonymous@undisclosed.example.com) — 2024-10-13T15:31:13+00:00

Freezer monitoring system One of the first projects I did a couple years ago, was designing a custom freezer monitoring system. It's end purpose was monitoring -80°C freezer, but I tested them successfully in liquid nitrogen, down to -196°C.

inwalltouchscreen

Anonymous (anonymous@undisclosed.example.com) — 2024-10-13T10:15:59+00:00

In wall touchscreen The in-wall touchscreen is a fairly easy setup, using an Raspberry pi 3+ with POE+ shield. Installation A hole was created in the wall during room renovations. This hole was measured to be the size of an 7 inch raspberry pi touchscreen, which is held in place using 2 strong neodymium magnets. Power is provided over POE+ from a Ubiquiti POE switch.

ledlightsceiling

Anonymous (anonymous@undisclosed.example.com) — 2024-10-13T15:09:46+00:00

Ledlights ceiling After moving to my new address, I decided to design my own custom led-lights with in-wall touchscreen monitor for control. This by connecting them to a wired Xnorduino communication bus. Note: * The camera strobing effect from the LED-drivers, is

rpizerocamera

Anonymous (anonymous@undisclosed.example.com) — 2024-10-13T11:25:27+00:00

Raspberry Pi Zero cam I setup a small RPI-zero camera, in order to know what's happening at my front-door and drive-way. Software The setup runs on motionEyeOS and is only available in my LAN network. Any movement within the camera's view automatically triggers a video recording, saved on the local SD card. I also added an additional custom script to the setup, that uploads an image file to a private Discord server as backup. This also provides an update on our phones, whenever someone's a…

start

Anonymous (anonymous@undisclosed.example.com) — 2024-10-09T16:22:51+00:00

Nothing to see here! Go back one page using the menu above…

xnorduino

Anonymous (anonymous@undisclosed.example.com) — 2026-03-08T14:09:04+00:00

Xnorduino Most embedded projects are based upon the same concept, of reading out a sensor and/or controlling an end device. I started the Xnorduino project, in an attempt of limiting the amount of repetitive rework in-between multiple unrelated projects. A Master-Slave communication bus setup was used, in order to accomplish this goal.

zigbeecarportcontroller

Anonymous (anonymous@undisclosed.example.com) — 2024-10-13T14:50:17+00:00

Carport controller I designed a custom wireless ZigBee carport controller, in order to minimize risk of accidentally locking ourselves out of the house. I decided to use the XBEE3 MMT chip, as these are compact, easy to use and receive regular firmware updates from the manufacturer Digi. They also support security features and have AES encrypted communication.